Getting Started with the MPC5775B BMC + MC33771 BCC high-voltage BMS system

最終更新日時： 2020-06-09 19:23:00サポート MPC5775B and MC33771 high-voltage BMS Evaluation System

このドキュメントの内容

  • 1

    Get Software

  • 2

    Plug It In

  • 3

    Build, Load

    お客様の MPC5775B and MC33771 high-voltage BMS Evaluation System

    このドキュメントの内容

    1. Get Software

    1.1 Get Started With the MPC5775B/E-EVB

    Let's take your MPC5775B battery management controller (BMC) plus MC33771 battery cell controller (BCC) high-voltage (HV) battery management system (BMS) for a test drive!

    1.2 Download the MPC5775B-BatterySystem_SDK

    Jump-start demo software for the MPC5775B-EVB using S32SDK 3.0.0 with FreeRTOS based on the S32 Design Studio IDE

    Download

    1.3 Download the MPC5775B-BatterySystem_GUI

    Graphic User Interface (GUI) software to monitor battery status using the CAN interface

    Download

    1.4 Get Your Integrated Development Environment (IDE)

    The MPC5775B BMC + MC33771 BCC HV BMS system performs better when using S32 Design Studio for Power Architecture® IDE

    Note: Check the S32 Design Studio page for the latest version.

    Download

    1.5 Get Python 3.7

    Install Python 64-bit version, also PyQt5 and NumPy packages.

    Download

    次へPlug It In

    2. Plug It In

    2.1 Connect BATT-14CEMULATOR and RD33771CDSTEVB

    Connect the BATT-14CEMULATOR battery cell emulator board and the RDCV33771C cell controller board using Cable_1.

    2.2 Connect RD33771CDSTEVB and MPC5775B-EVB

    Connect the RDCV33771C cell controller board with your MPC5775B-EVB battery management board using the Cable_2 to establish the TPL link for communication. Either J1 or J2 can be connected to the RD33771CDSTEVB. NOTE: connect positive (+) terminal of MPC5775B-EVB's BMS interface connector (J118 - pin 3,4 ) to BMS cell controller module positive (+) terminal and negative terminal to negative terminal.

    2.3 Power Up BATT-14CEMULATOR and RD33771CDSTEVB

    Plug the power supply to the BATT-14CEMULATOR battery cell emulator board.
    Powering the BATT-14CEMULATOR also powers the RDCV33771C cell controller board.

    2.4 Connect the USB Serial Cable to MPC5775B-EVB and PC

    Connect the micro-USB cable to J116 micro-USB port for OpenSDA connection for programming and debug. Connect the USB side to the computer.

    Note: check the MPC5775B/E low-cost development boards - Quick Start Guide

    2.5 Power the MPC5775B-EVB

    Connect 12 V power supply to power socket on your MPC5775B-EVB low-cost development board.

    Make sure the status LEDs D14, D15, D16, and D32 for voltage levels 3.3 V, 5 V, 1.25 V and 12 V supply respectively are glowing green on the board.

    2.6 Connect the CAN With PCAN Tool

    Connect CAN High and Low signals of J78 to PCAN tool CAN high and low. MPC5775B-EVB:

    J78 pin 2 is CAN0_High

    J78 pin 3 is CAN0_Low

    Connect the CAN_H and CAN_L signals of J78 of MPC5775B-EVB to PCAN USB CAN_H (pin 7) and CAN-L (pin 2) via two jumper cables.

    前へGet Software
    次へBuild, Load

    3. Build, Load

    3.1 Import the Demo Project Using Your IDE

    Import the MPC5775B_BMS_SDK_SW project into S32 Design Studio for Power Architecture®IDE

    3.2 Generate Processor Expert Codes and Compile the Binary Image

    Build and run the program to generate the processor expert codes, compile and build the image.

    Note: check the MPC5775B/E low-cost development boards - Quick Start Guide for debug/flash the image

    3.3 Connect the PCAN Tool USB to the PC

    Connect the USB connector of PCAN tool to the computer USB port.

    3.4 Run the GUI Software

    Open the “Command Prompt” from Windows and execute the Py Main.py (file included in the GUI folder) in the command shell.

    Make sure you first install Python 3.7 64-bit version and PyQt5 and NumPy packages.

    Note: Refer the readme file in the downloaded software GUI folder.

    3.5 Setup the GUI Link

    1. Select CAN1
    2. Set CAN baud rate to 500Kbps
    3. Click Start, now the CAN link establish with the main controller board
    4. Click OK
    5. Initiate global reset to BMS system by clicking Global Reset
    6. Observe the battery pack information: the GUI interface after communication has been established:

    Adjust the battery levels via BATT-14CEMULATOR and observe the GUI for individual cell data in BCCDATA tab:

    前へPlug It In