LPC1833JBD144|Arm Cortex-M3|32-bit MCU

LPC1833JBD144|Arm Cortex-M3|32-bit MCU | NXP Semiconductors

The LPC185x/3x/2x/1x are Arm Cortex-M3 based microcontrollers for embedded applications. The Arm Cortex-M3 is a next generation core that offers system enhancements such as low power consumption, enhanced debug features, and a high level of support block integration.

The LPC185x/3x/2x/1x operate at CPU frequencies of up to 180 MHz. The Arm Cortex-M3 CPU incorporates a 3-stage pipeline and uses a Harvard architecture with separate local instruction and data buses as well as a third bus for peripherals. The Arm Cortex-M3 CPU also includes an internal prefetch unit that supports speculative branching.

The LPC185x/3x/2x/1x include up to 1 MB of flash and 136 kB of on-chip SRAM, 16 kB of EEPROM memory, a quad SPI Flash Interface (SPIFI), a State Configurable Timer (SCT) subsystem, two High-speed USB controllers, Ethernet, LCD, an external memory controller, and multiple digital and analog peripherals.

製品画像を見る

データ・シート

アプリケーション・ノート

製品詳細

Features

Processor core
- Arm Cortex-M3 processor, running at CPU frequencies of up to 180 MHz
- Arm Cortex-M3 built-in Memory Protection Unit (MPU) supporting eight regions
- Arm Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC)
- Non-maskable Interrupt (NMI) input
- JTAG and Serial Wire Debug, serial trace, eight breakpoints, and four watch points
- Enhanced Trace Module (ETM) and Enhanced Trace Buffer (ETB) support
- System tick timer
On-chip memory
- Up to 1 MB on-chip dual bank flash memory with flash accelerator
- 16 kB on-chip EEPROM data memory
- 136 kB SRAM for code and data use
- Multiple SRAM blocks with separate bus access
- 64 kB ROM containing boot code and on-chip software drivers
- 64 bit of One-Time Programmable (OTP) memory for general-purpose use
Clock generation unit
- Crystal oscillator with an operating range of 1 MHz to 25 MHz
- 12 MHz internal RC oscillator trimmed to 2 % accuracy over temperature and voltage (1 % accuracy for T_amb = 0 °C to 85 °C)
- Ultra-low power RTC crystal oscillator
- Three PLLs allow CPU operation up to the maximum CPU rate without the need for a high-frequency crystal. The second PLL can be used with the High-speed USB, the third PLL can be used as audio PLL
- Clock output
Configurable digital peripherals
- State Configurable Timer (SCT) subsystem on AHB
- Global Input Multiplexer Array (GIMA) allows to cross-connect multiple inputs and outputs to event driven peripherals like timers, SCT, and ADC0/1
Serial interfaces
- Quad SPI Flash Interface (SPIFI) with 1-, 2-, or 4-bit data at rates of up to 52 MB per second
- 10/100T Ethernet MAC with RMII and MII interfaces and DMA support for high throughput at low CPU load. Support for IEEE 1588 time stamping/advanced time stamping (IEEE 1588-2008 v2)
- One High-speed USB 2.0 Host/Device/OTG interface with DMA support and on-chip high-speed PHY (USB0)
- One High-speed USB 2.0 Host/Device interface with DMA support, on-chip full-speed PHY and ULPI interface to an external high-speed PHY (USB1)
- USB interface electrical test software included in ROM USB stack
- Four 550 UARTs with DMA support: one UART with full modem interface; one UART with IrDA interface; three USARTs support UART synchronous mode and a smart card interface conforming to ISO7816 specification
- Up to two C_CAN 2.0B controllers with one channel each. Use of C_CAN controller excludes operation of all other peripherals connected to the same bus bridge
- Two SSP controllers with FIFO and multi-protocol support. Both SSPs with DMA support
- One Fast-mode Plus I²C-bus interface with monitor mode and with open-drain I/O pins conforming to the full I²C-bus specification. Supports data rates of up to 1 Mbit/s
- One standard I²C-bus interface with monitor mode and standard I/O pins
- Two I²S interfaces with DMA support, each with one input and one output
Digital peripherals
- External Memory Controller (EMC) supporting external SRAM, ROM, NOR flash, and SDRAM devices
- LCD controller with DMA support and a programmable display resolution of up to 1024H x 768V. Supports monochrome and color STN panels and TFT color panels; supports 1/2/4/8 bpp Color Look-Up Table (CLUT) and 16/24-bit direct pixel mapping
- SD/MMC card interface
- Eight-channel General-Purpose DMA controller can access all memories on the AHB and all DMA-capable AHB followers
- Up to 164 General-Purpose Input/Output (GPIO) pins with configurable pull-up/pull-down resistors
- GPIO registers are located on the AHB for fast access. GPIO ports have DMA support
- Up to eight GPIO pins can be selected from all GPIO pins as edge and level sensitive interrupt sources
- Two GPIO group interrupt modules enable an interrupt based on a programmable pattern of input states of a group of GPIO pins
- Four general-purpose timer/counters with capture and match capabilities
- One motor control PWM for three-phase motor control
- One Quadrature Encoder Interface (QEI)
- Repetitive Interrupt timer (RI timer)
- Windowed watchdog timer
- Ultra-low power Real-Time Clock (RTC) on separate power domain with 256 bytes of battery powered backup registers
- Event recorder with three inputs to record event identification and event time; can be battery powered
- Alarm timer; can be battery powered
Analog peripherals
- One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s
- Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s. Up to eight analog channels total. Each analog input is connected to both ADCs
Unique ID for each device
Power
- Single 3.3 V (2.2 V to 3.6 V) power supply with on-chip internal voltage regulator for the core supply and the RTC power domain
- RTC power domain can be powered separately by a 3 V battery supply
- Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep power-down
- Processor wake-up from Sleep mode via wake-up interrupts from various peripherals
- Wake-up from Deep-sleep, Power-down, and Deep power-down modes via external interrupts and interrupts generated by battery powered blocks in the RTC power domain
- Brownout detect with four separate thresholds for interrupt and forced reset
- Power-On Reset (POR)
Available in LQFP208, LBGA256, LQFP144, and TFBGA100 packages

Target Applications

Industrial
Consumer
White goods
RFID readers
e-Metering

‌ ‌ ‌	‌ ‌	‌ ‌	‌ ‌	‌ ‌	‌ ‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌

設計・リソース

デザイン・ファイル

クイック・リファレンス設計・ファイルの種類.

5 設計・ファイル

シミュレーションとモデル
IBIS Model for LPC18xx and LPC43xx FET256-180-100

ZIP改訂 1Sep 12, 2017309.9 KBIBIS_LPC18xx_43xxFET256

アカウントが必要です
ダウンロードToggle Dropdown
- キューに追加
- キューから削除
- ファイルサイズが大きい場合にお勧めします。
- キューを表示
シミュレーションとモデル
BSDL for LPC18xx and LPC43xx

ZIP改訂 2Feb 27, 2018269.0 KBBSDL_LPC18XX_43XX

アカウントが必要です
ダウンロードToggle Dropdown
- キューに追加
- キューから削除
- ファイルサイズが大きい場合にお勧めします。
- キューを表示
シミュレーションとモデル
IBIS Model_LPC18xx_LPC43xxFBD208

ZIP改訂 2Mar 25, 2020377.4 KBIBIS_LPC18xx_LPC43xxFBD208
ダウンロードToggle Dropdown
- キューに追加
- キューから削除
- ファイルサイズが大きい場合にお勧めします。
- キューを表示
シンボルおよびフットプリント
LPC43xx/LPC18xx Eagle symbols

ZIP改訂 0Jun 3, 201614.9 KBLPC43XX-EAGLE-SYM

アカウントが必要です
ダウンロードToggle Dropdown
- キューに追加
- キューから削除
- ファイルサイズが大きい場合にお勧めします。
- キューを表示
シンボルおよびフットプリント
LPC18XX_43XX_SCH Orcad Symbols

ZIP改訂 1.0Apr 30, 201852.2 KBLPC18XX_43XX_SCH_1

アカウントが必要です
ダウンロードToggle Dropdown
- キューに追加
- キューから削除
- ファイルサイズが大きい場合にお勧めします。
- キューを表示

ハードウェア

クイック・リファレンスボードタイプ.

1-5 の 6 ハードウェア提供

エミュレータ、プローブ、プログラマ
Universal Multilink開発インターフェース

UMultilink
エミュレータ、プローブ、プログラマ
PEmicro Cyclone programmer

CYCLONE
エミュレータ、プローブ、プログラマ
PEmicro Cyclone FX programmer

CYCLONE-FX
追加ハードウェアを利用可能パートナー・ソリューションの特集を表示.
エミュレータ、プローブ、プログラマ
MCU-Link Pro Debug Probe

MCU-LINK-PRO
エミュレータ、プローブ、プログラマ
Universal Multilink FX高速開発インターフェース

U-MULTILINK-FX
評価・開発ボード
MPC5646C Devlce and Target Adapters

MPC5646C-DB

全て表示

1-5 の 12 ハードウェア提供

テストアクセサリ、デバッガ
Flasher Secure

Flasher Secure is a mass production programming system, capable of protecting the vendor’s IP regardless of the production site. It provides full control over the program...

By SEGGER Microcontroller GmbH Gold パートナー
テストアクセサリ、デバッガ
Cyclone Production Programmers

Programmer for stand-alone (or cloud-connected) in-circuit flash programming, debug, & test of many NXP MCUs. Sophisticated power mgmt and dyanmic data. FX line o...

By P & E Microcomputer Systems, Inc Gold パートナー
テストアクセサリ、デバッガ
Flasher Compact

Flasher Compact is the compact twin to the Flasher PRO, primarily designed for installation into production rigs or automated test equipment (ATE) where production space ...

By SEGGER Microcontroller GmbH Gold パートナー
テストアクセサリ、デバッガ
Multilink Debug Probes

Multilink debug probes are BDM/JTAG debug probes for various NXP devices. Universal models support SWO debug in NXP's MCUXpresso IDE. FX model features high-speed com...

By P & E Microcomputer Systems, Inc Gold パートナー
テストアクセサリ、デバッガ
Flasher Portable PLUS

Flasher Portable PLUS is an extremely portable flash programmer, specifically designed to meet the needs of production-grade flash programming in the field.

By SEGGER Microcontroller GmbH Gold パートナー
テストアクセサリ、デバッガ
J-Link PRO PoE

J-Link PRO PoE is a specialized programming / debug probe for creating test farms. It can draw power via Ethernet and supplies power to the target either via debug interf...

By SEGGER Microcontroller GmbH Gold パートナー
テストアクセサリ、デバッガ
J-Link PRO

J-Link PRO is an enhanced version of the SEGGER J-Link. This emulator supports ARM/Cortex devices. This has an Ethernet interface in addition to the USB interface. This ...

By SEGGER Microcontroller GmbH Gold パートナー
テストアクセサリ、デバッガ
Flasher Hub-12

The Flasher Hub-12 controls up to 12 Flasher Compacts so that they program simultaneously, creating a powerful gang programmer for efficient high-speed parallel programmi...

By SEGGER Microcontroller GmbH Gold パートナー
テストアクセサリ、デバッガ
J-Link EDU Mini

The J-Link EDU Mini is a stripped-down, budget-friendly model of the J-Link debug probe created for educational use. Even with its reduced size, it maintains most J-Link ...

By SEGGER Microcontroller GmbH Gold パートナー
テストアクセサリ、デバッガ
Flasher PRO

Flasher PRO is SEGGER’s “almost-anything” flash programmer for microcontrollers, SoCs, and (Q)SPI flashes.

By SEGGER Microcontroller GmbH Gold パートナー
テストアクセサリ、デバッガ
Flasher ATE

Flasher ATE is perfectly suited for high volume mass production environments.

By SEGGER Microcontroller GmbH Gold パートナー
テストアクセサリ、デバッガ
J-Link ULTRA+

The J-Link ULTRA+ is three times faster than the industry standard J-Link, at a 3 MBytes/s download speed to RAM. It comes complete with J-Flash, and Unlimited Flash Brea...

By SEGGER Microcontroller GmbH Gold パートナー