LPC4367JET256|Arm Cortex-M4/M0|32-bit MCU

The LPC436x are Arm Cortex-M4 based microcontrollers for embedded applications, which include an Arm Cortex-M0 coprocessor and an Arm Cortex-M0 subsystem for managing peripherals, up to 1 MB of flash and 154 kB of on-chip SRAM, 16 kB of EEPROM memory, a quad SPI Flash Interface (SPIFI), advanced configurable peripherals such as the SCTimer/PWM and the Serial General Purpose I/O (SGPIO) interface, two High-speed USB controllers, Ethernet, LCD, an external memory controller, and multiple digital and analog peripherals. The LPC436x operate at CPU frequencies of up to 204 MHz.

The Arm Cortex-M4 is a 32-bit core that offers system enhancements such as low power consumption, enhanced debug features, and a high level of support block integration. The Arm Cortex-M4 CPU incorporates a 3-stage pipeline, uses a Harvard architecture with separate local instruction and data buses as well as a third bus for peripherals, and includes an internal prefetch unit that supports speculative branching. The Arm Cortex-M4 supports single-cycle digital signal processing and SIMD instructions. A hardware floating-point processor is integrated into the core.

The LPC436x include an application Arm Cortex-M0 coprocessor and a second Arm Cortex-M0 subsystem for managing the SGPIO and SPI peripherals.The Arm Cortex-M0 coprocessor is an energy-efficient and easy-to-use 32-bit core which is upward code- and tool-compatible with the Cortex-M4 core. The Cortex-M0 coprocessor, designed as a replacement for existing 8/16-bit microcontrollers, offers up to 204 MHz performance with a simple instruction set and reduced code size. In LPC436x, the Cortex-M0 coprocessor hardware multiply is implemented as a 32-cycle iterative multiplier.

製品画像を見る

データシート

アプリケーション・ノート

製品詳細

Features

Cortex-M4 Processor core
- Arm Cortex-M4 processor (version r0p1), running at frequencies of up to 204 MHz.
- Built-in Memory Protection Unit (MPU) supporting eight regions.
- Built-in Nested Vectored Interrupt Controller (NVIC).
- Hardware floating-point unit.
- Non-maskable Interrupt (NMI) input.
- JTAG and Serial Wire Debug (SWD), serial trace, eight breakpoints, and four watch points.
- Enhanced Trace Module (ETM) and Enhanced Trace Buffer (ETB) support.
- System tick timer.
Cortex-M0 Processor core
- Arm Cortex-M0 co-processor (version r0p0) capable of off-loading the main Arm Cortex-M4 application processor.
- Running at frequencies of up to 204 MHz.
- JTAG
- Built-in NVIC.
Cortex-M0 subsystem
- Arm Cortex-M0 coprocessor controlling the SPI and SGPIO residing on a separate AHB multilayer matrix. Includes 2 kB + 16 kB of SRAM.
- Running at frequencies of up to 204 MHz.
- Connected via a core-to-core bridge to the main AHB multilayer matrix and the main Arm Cortex-M4 processor.
- JTAG and built-in NVIC.
On-chip memory
- Up to 1 MB on-chip dual bank flash memory with flash accelerator.
- 16 kB on-chip EEPROM data memory.
- 154 kB SRAM for code and data use.
- Multiple SRAM blocks with separate bus access. Two SRAM blocks can be powered down individually.
- 64 kB ROM containing boot code and on-chip software drivers.
- 64 bit+ 256 bit of One-Time Programmable (OTP) memory for general-purpose use.
Configurable digital peripherals
- Serial GPIO (SGPIO) interface.
- SCTimer/PWM subsystem on AHB.
- Global Input Multiplexer Array (GIMA) allows to cross-connect multiple inputs and outputs to event driven peripherals like the timers, SCTimer/PWM, and ADC0/1.
Serial interfaces
- Quad SPI Flash Interface (SPIFI) with four lanes and up to 52 MB per second.
- 10/100T Ethernet MAC with RMII and MII interfaces and DMA support for high throughput at low CPU load. Support for IEEE 1588 time stamping/advanced time stamping (IEEE 1588-2008 v2).
- One High-speed USB 2.0 Host/Device/OTG interface with DMA support and on-chip high-speed PHY.
- One High-speed USB 2.0 Host/Device interface with DMA support, on-chip full-speed PHY and ULPI interface to external high-speed PHY.
- USB interface electrical test software included in ROM USB stack.
- One 550 UART with DMA support and full modem interface.
- Three 550 USARTs with DMA and synchronous mode support and a smart card interface conforming to ISO7816 specification. One USART with IrDA interface.
- Up to two C_CAN 2.0B controllers with one channel each.
- Two SSP controllers with FIFO and multi-protocol support. Both SSPs with DMA support.
- One SPI controller.
- One Fast-mode Plus I²C-bus interface with monitor mode and with open-drain I/O pins conforming to the full I²C-bus specification. Supports data rates of up to 1 Mbit/s.
- One standard I²C-bus interface with monitor mode and with standard I/O pins.
- Two I²S interfaces, each with DMA support and with one input and one output.
Digital peripherals
- External Memory Controller (EMC) supporting external SRAM, ROM, NOR flash, and SDRAM devices.
- LCD controller with DMA support and a programmable display resolution of up to 1024 H × 768 V. Supports monochrome and color STN panels and TFT color panels; supports 1/2/4/8 bpp Color Look-Up Table (CLUT) and 16/24-bit direct pixel mapping. Available on parts LPC4357/53 only.
- Secure Digital Input Output (SD/MMC) card interface.
- Eight-channel General-Purpose DMA controller can access all memories on the AHB and all DMA-capable AHB followers
- Up to 164 General-Purpose Input/Output (GPIO) pins with configurable pull-up/pull-down resistors.
- GPIO registers are located on the AHB for fast access. GPIO ports have DMA support.
- Up to eight GPIO pins can be selected from all GPIO pins as edge and level sensitive interrupt sources.
- Two GPIO group interrupt modules enable an interrupt based on a programmable pattern of input states of a group of GPIO pins.
- Four general-purpose timer/counters with capture and match capabilities.
- One motor control Pulse Width Modulator (PWM) for three-phase motor control.
- One Quadrature Encoder Interface (QEI).
- Repetitive Interrupt timer (RI timer).
- Windowed watchdog timer (WWDT).
- Ultra-low power Real-Time Clock (RTC) on separate power domain with 256 bytes of battery powered backup registers.
- Alarm timer; can be battery powered.
Analog peripherals
- One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s.
- Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s. Up to eight input channels per ADC.
Unique ID for each device.
Clock generation unit
- Crystal oscillator with an operating range of 1 MHz to 25 MHz.
- 12 MHz internal RC oscillator trimmed to 3 % accuracy over temperature and voltage (1.5 % accuracy for T_amb = 0 °C to 85 °C).
- Ultra-low power Real-Time Clock (RTC) crystal oscillator.
- Three PLLs allow CPU operation up to the maximum CPU rate without the need for a high-frequency crystal. The second PLL can be used with the High-speed USB, the third PLL can be used as audio PLL.
- Clock output.
Power
- Single 3.3 V (2.4 V to 3.6 V) power supply with on-chip DC-to-DC converter for the core supply and the RTC power domain.
- RTC power domain can be powered separately by a 3 V battery supply.
- Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep power-down.
- Processor wake-up from Sleep mode via wake-up interrupts from various peripherals.
- Wake-up from Deep-sleep, Power-down, and Deep power-down modes via external interrupts and interrupts generated by battery powered blocks in the RTC power domain.
- Brownout detect with four separate thresholds for interrupt and forced reset.
- Power-On Reset (POR).
Available as LQFP208, LBGA256, or TFBGA100 packages.

Target Applications

Industrial HMI
Secure IoT Gateways
Industrial automation
Industrial control
Consumer health devices
Communication hubs
Embedded audio applications
Automotive aftermarket
White goods

購入/パラメータ

‌ ‌ ‌	‌ ‌	‌ ‌	‌ ‌	‌ ‌	‌ ‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌
‌ ‌ ‌	‌	‌	‌	‌	‌

ドキュメント

クイック・リファレンスドキュメンテーションの種類.

1-5 の 12 ドキュメント

データ・シート
32-bit Arm^® Cortex^®-M4/M0 MCU; up to 1 MB flash and 154 kB SRAM; Ethernet, two High-speed USB, LCD, EMC

PDF改訂 1.3Feb 5, 20207.2 MBLPC436X
アプリケーション・ノート
USBD Library for LPC4300/LPC1800 series MCUs

ZIP改訂 1.0Jul 9, 20188.6 MBTN00041
アプリケーション・ノート
Connecting TFT LCD with LCD controller of LPC MCU

ZIP改訂 1Aug 22, 20173.2 MBAN12027
アプリケーション・ノート
SCTimer/PWM cookbook

ZIP改訂 5.0Mar 22, 201625.5 MBAN11538, 中文
アプリケーション・ノート
Code Read Protection in LPC1800 and LPC4300

ZIP改訂 1.0Aug 14, 201416.6 MBAN11581
アプリケーション・ノート
Implementing PWM dithering on the LPC18xx SCTimer/PWM

ZIP改訂 1.0Aug 8, 20141.7 MBAN11580
アプリケーション・ノート
SCT camera interface design with LPC1800 and LPC4300

ZIP改訂 1.2Jun 12, 20141.4 MBAN11365
アプリケーション・ノート
AES encryption and decryption software on LPC microcontrollers

ZIP改訂 1.1Mar 17, 2014177.9 KBAN11241
ユーザ・ガイド
LPC43xx/LPC43Sxx Arm® Cortex®-M4/M0 multi-core microcontroller

PDF改訂 2.5Sep 13, 201913.6 MBUM10503

アカウントが必要です
エラッタ
Errata sheet LPC436x flash-based devices

PDF改訂 2.3Feb 5, 2020463.6 KBES_LPC436X_FLASH
パッケージ情報
plastic low profile ball grid array package; 256 balls; body 17 x 17 x 1 mm

PDF改訂 1.0Feb 8, 2016644.0 KBSOT740-2
レポートまたはプレゼンテーション
Driving LPC1700/LPC1800/LPC4300 with EPSON Crystals

PDF改訂 1.1Nov 27, 2015213.7 KBR_10076

全て表示

設計・リソース

デザイン・ファイル

クイック・リファレンス設計・ファイルの種類.

2 設計・ファイル

完全な内訳を受け取ります。 製品の設置面積などについては、 eCad ファイル.

シミュレーションとモデル
BSDL for LPC18xx and LPC43xx

ZIP改訂 2Feb 27, 2018 11:57:00269.0 KBBSDL_LPC18XX_43XX

アカウントが必要です
ダウンロードToggle Dropdown
- キューに追加
- キューから削除
- ファイルサイズが大きい場合にお勧めします。
- キューを表示
シンボルおよびフットプリント
LPC43xx/LPC18xx Eagle symbols

ZIP改訂 0Jun 3, 2016 00:00:0014.9 KBLPC43XX-EAGLE-SYM

アカウントが必要です
ダウンロードToggle Dropdown
- キューに追加
- キューから削除
- ファイルサイズが大きい場合にお勧めします。
- キューを表示

ハードウェア

クイック・リファレンスボードタイプ.

1-5 の 6 ハードウェア提供

評価・開発ボード
LPCXpresso4367 Development Board注目

OM13088
エミュレータ、プローブ、プログラマ
Universal Multilink開発インターフェース

UMultilink
エミュレータ、プローブ、プログラマ
PEmicro Cyclone programmer

CYCLONE
追加ハードウェアを利用可能パートナー・ソリューションの特集を表示.
エミュレータ、プローブ、プログラマ
PEmicro Cyclone FX programmer

CYCLONE-FX
エミュレータ、プローブ、プログラマ
Universal Multilink FX高速開発インターフェース

U-MULTILINK-FX
評価・開発ボード
Hitex LPC4350 Evaluation board

OM13031

全て表示

4 ハードウェア提供

評価・開発ボード
LPC4357 Developer's Kit

Embedded Artists' LPC4357 Developer's Kit lets you get up-and-running quickly with the LPC4357 OEM board, for rapid prototyping and proof-of-concept designs. The developm...

By Embedded Artists AB Gold パートナー
テストアクセサリ、デバッガ
Flasher Compact

Flasher Compact is the compact twin to the Flasher PRO, primarily designed for installation into production rigs or automated test equipment (ATE) where production space ...

By SEGGER Microcontroller GmbH Gold パートナー
テストアクセサリ、デバッガ
LPCXpresso Click Shield

LPCXpresso Click Shield designed to support multiple NXP development platforms that use Arduino connector and equip them with two mikroBUS sockets.

By MIKROE Gold パートナー
テストアクセサリ、デバッガ
J-Link PRO PoE

J-Link PRO PoE is SEGGER's specialized programming / debug probe for creating test farms. It can draw power via Ethernet and supplies power to the target either via d...

By SEGGER Microcontroller GmbH Gold パートナー