デザイン・ファイル
完全な内訳を受け取ります。 製品の設置面積などについては、 eCad ファイル.
8-bit General Purpose SH MCUs
The S08SH family is a series of S08 8-bit microcontrollers that offer a new low-end option for applications in the 5-volt range. The S08SH family is pin, tool and software compatible with S08SG, offering greater design flexibility. It also has wide peripheral offering with serial communications interface (SCI), serial peripheral interface (SPI), I²C, analog-to-digital converter (ADC), analog comparator and temperature sensor.
製品詳細
Features
8-bit HCS08 Central Processor Unit (CPU)
- Up to 40 MHz HCS08 CPU (20 MHz bus frequency) for 50 ns minimum instruction time
- HC08 instruction set with added BGND instruction
- Support for up to 32 interrupt/reset sources
Integrated Third-Generation Flash Memory and RAM
- Embedded flash that is in-application reprogrammable
- Fast, byte-writable programming, as fast as 20 µs/byte
- Up to 100,000 write/erase cycles at typical voltage and temperature (10k minimum write/erase)
- 100 years typical data retention (15 years minimum)
Flexible Clock Options
- Internal clock source (ICS) module containing a frequencylocked loop (FLL) controlled by internal or external reference
- Precision trimming of internal reference allows typical 0.1 percent resolution and +0.5 percent to -1 percent deviation over operating temperature and voltage
- Internal reference can be trimmed from 31.25 kHz to 39.065 kHz, allowing for 16 MHz to 20 MHz FLL output
- Low-power oscillator module (XOSC)
- software selectable crystal or ceramic resonator range, 31.25 kHz to 38.4 kHz or 1 MHz to 16 MHz,
- supports external clock source input up to 40 MHz
Input/Output
- Up to 23 bidirectional lines
- One Output-Only Line
- Outputs 10 mA each; 60 mA max for package
- Software selectable pull-ups on ports when used as input
- internal pull-up on reset and interrupt request (IRQ) pin
- Software selectable slew rate control and drive strength on ports when used as output
- 8-pin keyboard interrupt module with software selectable polarity on edge or edge/level modes
Ganged Output Option for PTB (5:2) and PTC (3:0)
- Allows single write to change state of multiple pins
- Drives up to 80 mA without risk of runaway code shorting
- Provides option to tie multiple pins from different ports to same control registers
- Safely drives multiple outputs
Multiple Serial Communication Options
- Serial communications interface module with option for 13-bit break capabilities and double-buffered transmit and receive
- Serial peripheral interface module and I²C bus module
Integrated Analog Peripherals
- 16-ch., 10-bit analog-to-digital converter (ADC)
- Automatic compare function, software programmable for greater than/equal to or less than conditions
- Asynchronous clock source
- Temperature sensor
- Internal bandgap reference channel
- Hardware triggerable using the RTI counter
- Low-power and high-speed options
- Analog comparator module (ACMP)
- Option to compare to internal reference
- Option to route comparator output directly to pin
- Output can be optionally routed to TPM module as input capture trigger
- Real-time-counter (RTC)
- 8-bit modulus counter with binary or decimal based prescaler
- External clock source for prescise time base, time-of-day, calendar or task scheduling functions
Three Timer Modules
- Programmable 16-bit timer/PWM modules (TPM1 and TPM2)
- 8-bit modulo timer module (MTIM) with 8-bit prescaler
System Protection
- Watchdog computer operating properly (COP) reset with option to run from dedicated 1 kHz internal clock source or bus clock
- Low-voltage detection with reset or interrupt
- Illegal opcode detection with reset
- Flexible block protection
- Security feature for flash and RAM
- Always-on power-on reset (POR) circuitry
Development Support
- Background Debugging System
- On-Chip In-Circuit Emulation (ICE)
- Real-Time Bus Capture
S08SH Family Comparison
| Features | S08SH | S08SG | S08QG | S08QD | RS08KA |
| Core | HCS08 | HCS08 | HCS08 | HCS08 | RS08 |
| Operating Voltage (V) | 2.7 - 5.5 | 2.7 - 5.5 | 1.8 - 3.6 | 2.7 - 5.5 | 1.8 - 5.5 |
| Bus Frequency (MHz) | 20 | 20 | 10 | 8 | 10 |
| Flash (Kbyte) | 4 / 8 | 4 / 8 / 16 / 32 | 4 / 8 | 2 / 4 | 1 / 2 |
| RAM (byte) | 256 / 512 | 256 / 512 / 1024 | 256 / 512 | 128 / 256 | 63 |
| Serial Comunications | SCI/w LIN Support
SPI I²C |
SCI
SPI I²C |
SCI
SPI I²C |
None | None |
| ADC | Up to 12 channels (10 bits) | Up to 16 channels (10 bits) | Up to 8 channels (10 bits) | Up to 4 channels (10 bits) | None |
| Analog Comparator | Yes | Yes | Yes | No | Yes |
| Timers | Up to Two Timers 16-bits (2 Channels each) | Up to Two Timers 16-bits (2 channels each) | One Timer 16-bit (2 channels)
One 8-bit |
Two Timers 16-bit (2 and 1 channels) | One Timer 8-bits |
| Tempeature Ranges (°C) | -40 to 85
-40 to 125 |
-40 to 85
-40 to 105 -40 to 125 |
-40 to 85 | -40 to 85
-40 to 105 -40 to 125 |
-40 to 85 |
| Package | 8-pin SOIC
16-pin TSSOP 20-pin PDIP/TSSOP 24-pin QFN |
8-pin SOIC
16-pin TSSOP 20-pin TSSOP 24-pin TSSOP 28-pin TSSOP |
8-pin DIP/SOIC/QFN
16-pin DIP/TSSOP/QFN |
8-pin DIP/SOIC | 6-pin QFN
8-pin DIP/SOIC |
S08SH Family is pin, tool and software compatible with S08SG, offering greater design flexibility.
購入/パラメータ
|
|
|
|
|
|
|
|---|---|---|---|---|---|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
ドキュメント
クイック・リファレンス ドキュメンテーションの種類.
1-5 の 23 ドキュメント
-
データ・シート
MC9S08SH16/MC9S08SH16 - Data Sheet注目
-
データ・シート
MC9S08SH8 - Data Sheet注目
-
ファクト・シート
S08SH16/32 Fact Sheet注目
-
ファクト・シート
MC9S08SH8/4 - Fact sheet注目
設計・リソース
ハードウェア
クイック・リファレンス
ボードタイプ.
5 ハードウェア提供
-
エミュレータ、プローブ、プログラマUniversal Multilink開発インターフェース注目
-
評価・開発ボードS08SH Family Demonstration Board注目
-
エミュレータ、プローブ、プログラマPEmicro Cyclone programmer
-
エミュレータ、プローブ、プログラマPEmicro Cyclone FX programmer
-
エミュレータ、プローブ、プログラマUniversal Multilink FX高速開発インターフェース
ソフトウェア
クイック・リファレンス ソフトウェア・タイプ.
1-5 の 11 ソフトウェア・ファイル
-
BSPとデバイスドライバ
Graphical LCD Driver for MCUs/MPUs注目
-
追加ソフトウェアを利用可能 パートナー・ソリューションの特集を表示.
注: より快適にご利用いただくために、ソフトウェアのダウンロードはデスクトップで行うことを推奨します。
エンジニアリング・サービス
NXPから直接サポートを受けるには、以下のサイトをご覧ください。 エンジニアリング・サービス.
1 エンジニアリング・サービス
-
インディペンデントデザインハウス (IDH)
ハードウェア/ソフトウェア・エンジニアリング・サービス
この製品をサポートするその他のパートナー製品を見つけるには、当社の Web サイトにアクセスしてください パートナーマーケットプレイス.